There are some common issues that homeowners face with their garage doors. If you notice that your garage door has been malfunctioning for quite some time, there are some easy things you can do to fix the issue. Broken torsion springs, damaged photo-eye sensors, faulty rollers, and more can be fixed with little DIY knowledge. Read on to discover some of the most common problems with your garage door.
Broken Torsion Springs
Broken torsion springs are standard garage door problems, but don’t try to repair them yourself! You could end up with a garage door that doesn’t open or close properly. If you can’t figure out what’s wrong, you should call a professional for help. Broken torsion springs are dangerous because they operate under significant tension and energy. Again, do-it-yourselfers should call Seattle garage door repair professionals for this job.
To replace a broken torsion spring, you’ll need to measure the size of the torsion spring. These springs vary in size and are often rated for 20,000 cycles. To determine the correct size, you’ll need to measure each coil and convert the measurement to decimal. You’ll want to divide the measurement by 20 or 40. Once you have the wire diameter, you’ll need to measure the spring’s length.https://www.google.com/maps/embed?pb=!1m18!1m12!1m3!1d2688.8622279308775!2d-122.1709612!3d47.6288093!2m3!1f0!2f0!3f0!3m2!1i1024!2i768!4f13.1!3m3!1m2!1s0x0%3A0x910916bec0f83434!2sLexD%20-%20Seattle%20Area%20Garage%20Door%20Company!5e0!3m2!1sen!2sus!4v1655317033450!5m2!1sen!2sus
Damaged Photo-Eye Sensors
One of the most common garage door problems is damaged photo-eye sensors. This can be a simple DIY job. However, if you’re unsure how to fix this problem, you might need to call in a technician. The wiring that powers photo-eye sensors is susceptible to breakage, and a damaged wire might mean the photo-eye is out of alignment. You should first block the sun’s rays from the sensors.
If you notice the sensor doesn’t work, there are several ways to fix it. First, check to see if it’s plugged into the wall. If the light is off, you might have bumped it. Meanwhile, if it’s not, adjust the sensor by hand. Finally, try wiping it with a damp cloth if it’s dirty. You may also need to clean the lenses with a damp cloth to remove any accumulated dirt on them.
Unplugged Motors
If your garage door is not opening, there are several common causes of this issue. If the door opener switch is not working, it is most likely the motor. To remedy this issue, unplug the motor, usually located near the ceiling. If the door is not opening due to a lock switch, you must disengage it. Here are some common problems that cause a malfunctioning garage door opener.
The motor may not be plugged in. In such a case, you will need to check the wiring of the motor. In addition, some openers are not compatible with universal voltage adapters. You can also check the door’s limits if you’re unsure what they are. Garage door openers can also cause problems if the limit is too high. Listed below are some of the most common issues with garage doors.
Broken Rollers
If your garage door moves slowly, you may have a problem with the rollers. If you live in a dry climate, rollers can become dried out. Additionally, freezing and rusting of the rollers can cause the door to move slowly. Several tips to prevent these problems include wiping the tracks and rollers, lubricating the rollers, and tightening hardware. These are the most common problems encountered with garage doors.
One of the most common problems affecting garage doors is the broken rollers. These components guide the door to its overhead position. Over time, rollers can become bent or dislocated. If these parts fail to move smoothly, the door may jump off its tracks. It may also become uneven and jerky, which could damage the opener. Of course, you may be able to swap out the rollers yourself. Still, you may want to contact a professional garage door repair company if you don’t feel confident in your skills.
Broken Glass
There are some reasons why broken glass in garage doors could be a problem. These include play activities and the occasional impact from a baseball. While a broken garage door may not be a safety issue, it could be a security hazard and invite unwanted visitors. The good news is that it’s a relatively easy task. You can simply replace the broken glass in your garage door with the same process as you would for window panes.
If your garage door has broken glass, the first step is to remove it. It is best to do this as soon as possible. However, it’s essential to take safety precautions and wear safety glasses. While replacing glass in garage doors is not difficult, it’s vital to avoid getting hurt while working on it. The door’s frame should be carefully cleaned, and the glass must be adequately measured. Wearing safety glasses and gloves is recommended, as broken glass could be dangerous. Also, you should ensure that you have access to your garage door. This is especially important during colder months.
Broken Cables
If your cables have snapped or are frayed, it’s time to call a garage door repair service. A broken cable can be a potentially dangerous situation, and you must have them inspected by a professional to prevent this from happening. Here are some warning signs of trouble:
Firstly, fraying can be caused by friction between the cable sleeve and the door. It often occurs near the sleeve end. If you have a box truck-style door, the cable spool must be inserted inside the loop to avoid fraying. Fraying in cables is a common problem and can lead to the door not functioning properly. Fortunately, there are a few simple ways to check the wires.
